Type C3.1加長母座轉A公大電流 雙56K電容/電阻帶音頻數據Type-C 接口進行供電了但身邊還是有很多老舊設備依然用著 Micro-USB 接口進行供電，抽屜里各種接口充電線一大堆，每次外出也要帶上好幾根線是在是麻煩，蘋果也要從 Lightning 接口換成 Type-C 接口了，為提前完成設備接口大一統，于是就有了此次 Micro-USB 裝 Type-C 的想法。 充電寶的拆開方法這里不做過多描述，Micro-USB 接口，往電路板接口處涂上松香，使用電烙鐵將電路板 Micro-USB 接口焊接出來，這里直接放已經拆完 Micro-USB 母座的電路板照片。Type-C 母座處理，在 Type-C 母座的兩個 CC 引腳處使用 5.1kΩ 貼片電阻接地。引腳定義圖，這里放上 Micro-USB 與 6Pin Type-C 的引腳定義圖，找到電路板的正負極（VBUS與GND）電路并做好標記。 電路板涂 AB 膠，取 AB 膠混合均勻后涂抹到電路板Type-C 母座涂 AB 膠，往母座光滑的背面涂上 AB 膠，并固定在電路板上， 焊接正負極（VBUS與GND引腳），使用細導線焊接 Type-C 的正負極引腳到主板上的正負極處，電路焊接完成后再使用 AB 膠進行最后的加固。處理外殼充電口大小，使用美工刀、電磨等工具將充電寶外殼充電口擴大。Type-C 的 CC1、CC2 引腳用于 PD 設備識別，承載 USB-PD 的通信，引腳如果沒有接 5.1kΩ 電阻接地，那么使用普通 AtoC 數據線依然是可以供電的，但如果使用 PD 充電器的 CtoC 數據線供電，充電頭就會拒絕供電。由于 6Pin Type-C 的引腳僅保留 Vbus、GND、CC1、CC2，對于玩具、牙刷等產品定位上沒有 USB 通信的需求生活用品，只需要 USB 取電進行充電，那么 6Pin Type-C 夠用了，如果需要傳數據的話，則需要 12Pin、16Pin 甚至 24Pin 的 Type-C。